Zuhause> Blog> How does the gsm module communicate with the microcontroller?

How does the gsm module communicate with the microcontroller?

February 18, 2023
51 Single Chip Microcomputer and GSM Module Realize Communication

1, detect the serial line is good or bad

1) Plug the serial cable into the computer and short-circuit the 2 and 3 pins of the serial port

2) Open the serial debugging assistant

3) Click Auto-send, send a random data in the automatically sent window to see if it can receive the self-transmitted data that the serial line is normal, otherwise it is bad.

2, after the completion of the microcontroller program, take a look at the serial port for data detection

3, the meaning of the 4 lights that the module communicates with the module on the one-chip computer

1)DO lamp

Flashing indicates that the serial port of the SCM serial port and the GSM module are not communicating properly, otherwise the serial port communication is normal.

2) D1 light

The light indicates that the module is registered on the network, otherwise it is not registered on the network

3) D2 light

Lights up to start texting

4) D3 light

Lights up to end the text message

4. Connection of MCU board and GSM module

SCM ---------GSM module

VCC--------vcc (pin 3 of P5)

GND--------GND (pin 4 of P5)

RX_232 (indicating the sending of the SCM)----------RXDPC_232 (receiving of the module (pin 5 of P5))

TX_232 (represents the receipt of the SCM) ---------- TXD_PC232 (Send of the module (P5 pin 6))

How does the gsm module communicate with the microcontroller?

Gsm module and microcontroller connection

One-chip computer connects GSM module, can connect TX and RX of asynchronous serial communication port directly, do not forget the ground wire.

Precautions:

1. Different MCUs have different voltages. The input and output levels of the general GSM module are 2.85V, and the level of the 51 series is 5V. Generally, the resistance of the 2K series connected to the 51 output TX line can basically be used. If it is a 3.3V microcontroller, this resistance can be very small, a few hundred ohms can be.

2. The power supply of the GSM module and the SIM card circuit are very troublesome. First of all, most of the GSM modules use the interface of the FPC40. The distance between the cables is only 0.5mm, and it is a plastic case, which is not good for welding. If welding is not good, work is unstable. Followed by the more troublesome power supply, GSM module emission current is larger, the maximum instantaneous current 2A! Therefore, the power supply part generally uses a high-current DC-DC converter such as the LM2576 to provide a voltage of 4V. The design of the DCDC circuit itself is not easy, and it is difficult for a personal application to require a circuit board. Latency of instability. There is also a SIM card. The communication between the SIM card and the GSM module itself is a complicated high-frequency process. The circuit has strong anti-interference ability. I once tried to connect them with wires and dropped them in ten minutes. Therefore, the SIM card part needs to be carefully designed. Do not look at only five data lines.

MCU control TC35GSM module method 1, hardware connection

The circuit shown in the figure below only needs to design a TTL-to-RS232 level circuit, which is connected to the UART port of the MCU, and the other end is directly connected to the TC35.

How does the gsm module communicate with the microcontroller?

2, the instruction output method

The serial port of the one-chip computer sets up mode 1 (9600, N, 8, 1), export AT+xxx to UART port in ASCII code form sequentially ; The data of receiving TC35 adopts and cuts off the way. A detailed list of procedures (Keil C51) is given here, but the programming method is not described. The procedure is as follows:

// Definition of AT command

Char code AT_Tc35[]=“AT+”; //Consecutive

Char code Bps_Tc35[]=“IPR=38400”; //Baud rate

Char code Text_Tc35[]="CMGF=1"; //text mode

Char code Read_Tc35[]=“CMGR=”; //Read information

Char code Erase_Tc35[]=“CMGD=”; //Delete message

Char code Send_Tc35[]=“CMGS=”; //Send message

Char code Creg_Tc35[]=“CREG?”; //Register

//Mode setting

Void UART_Init(void)

{

SCON=0x50; //01010000b=”1 pattern scon,#11011000b;

ES=l;

}

// send - ASCII

Void SendASC(unsigned char ASC)

{

Bit es;

Es=ES;

ES=0;//Close interrupt

TI=0;

SBUF=ASC;

While(!TI);

TI=0;

ES=es;

)

//Send command to TC35

Void SendToTc35(unsigned char* p, unsigned char Long)

{

While(Long--)

{

SendASC(*p++);

}

}

// Communication interrupt receiver

Void Rs485_Do(void) interrupt 4 using 1

{

If (RI==l)

{

RI=0;

RsBuq[RsPoint++]=SBUF;

If fRsPoint" = sizeof(RsBuf))

{

RsPoint=0;//FlagRs485=0;

} //data processing

}

}

// Send AT command

Char code AT_Code[]=“OK”;

Void Send_AT(void)

{

Unsigned char *p;

While(1)

{

ClrRsBuf(RsBuf, sizeof(RsBuf));

SendToTc35(AT_Tc35,2); //"AT"

SendASC(OVER);

//************ Waiting for reply "ok"

ES=1; // must be interrupted

Delay(50);

P=strstr(RsBuf,AT_Code);

If(p!=NULL) break;

}

)

//Send bps machine command

Void Send_BPS(void)

{

SendToTc35(AT_Tc35,3); //"AT+"

SendToTc35(Bps_Tc35, sizeof(Bps_Tc35)-1); //"IPR=19200"

SendASC(OVER);

}

//Set text

Void SetText(void)

{

SendToTc35(AT_Tc35,3); //"AT+"

SendToTc35(Text_tc35, sizeof(Text_tc35)-1);//IPR=19200"

SendASC(OVER);

Delay(100):

//Delete SMS

Unsigned char EraseMsg(unsigned char index)

{

Unsigned char *p,i=20;

SendToTc35(AT_Tc35,3); //"AT+"

SendToTc35(Erase_Tc35, sizeof(Erase_Tc35)-1);//IPR=19200"

SendASC(index);

SendASC(OVER);

ES=1;

While(i--)

{

Delay(200);

P=strstr(RsBuf,AT_Code);

If(P!=NULL) {return 1;}

}

Return 0;

}

//Read SMS

Char code Ask_No[]=”+CMGR:0,,0”;

Char code ERROR{]=”ERROR”;

Char code Ask_Tc35[]=”/“;

Unsigned char ReadMsg(unsigned char index)

{

Unsigned char *p,i;

Unsigned char Buf[40];

SendToTc35(AT_Tc35,3); //"AT+"

SendToTc35(Read_Tc35,sizeof(Read_Tc35)-1);

SendASC(index);

SendASC(OVER);

ES=1; // must be interrupted

Delay(600);

/*-------

ES=0:

SendToTc35(RsBuf,99);

ES=1;

*/|

p=strstr(RsBuf,ERROR);

If(P!=NULL)

{

Send_AT();return 0;

p=strstr(RsBuf,Ask_No);//No information

If(p!=NULL)return 0;

p=strstr(RsBuf,Ask_Tc35);//20 bytes after MSG

If(p==NULL) return 0;

p=p+21;

For(i=0;i<<sizeof(Buf);i++)

{

Buf[i]=*p++;

}

If(EraseMsg(index)==0) return 0;

p=strcpy(RsBuf,Buf); //Return to RsBuf

Return 1;

)

//Send SMS

Char code SK[]=”";

Void SendMsgStart(void)

{

Unsigned char *p,i=10;

SendToTc35(AT_Tc35,3); //"AT+"

SendToTc35(Send_Tc35, sizeof(Send_Tc35)-1);//IPR=19200"

SendASC(YinHao);

SendToTc35(Mp1.Hand, sizeof(Mp1.Hand)); //"AT+"

SendASC(YinHao);

SendASC(OVER);

ES=1;

While(i--)

{

Delay(100); //Get"" "

p=strstr(RsBuf,SK);//"""

If(p!=NULL)

{

ClrRsBuf(RsBuf, sizeof(RsBuf));

Delay(150); //Get"" "

Break;

}

}

}

Kontaktiere uns

Author:

Ms. Zoe Zhong

Phone/WhatsApp:

+86 18617178558

beliebte Produkte
You may also like
Related Categories

Mail an Lieferanten

Fach:
Mobiltelefon:
E-Mail-Adresse:
Nachrichten:

Your message must be betwwen 20-8000 characters

Kontakten

  • Telefonnummer: 86-186-17178558
  • Whatsapp: +86 18617178558
  • E-Mail-Adresse: sales07@ynxantenna.com
  • Firmenadresse: Room #101,201,301,5BLDG , No.4 of XinWuCun New Area ,Shabo community Maluan Street Pingshan District, Shenzhen ,Guangdong , China, Shenzhen, Guangdong China

Send Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

senden